Lund Industries

Special Mounts

CV-HSM
Swing open mount for RLS, Smart, or MPCO1 siren control heads. A convenient alternative when a console isn’t necessary. Installs over factory radio location and still allows access to the radio volume control. Latches in place.

LKP-FKB
Universal 9" to 13" adjustable floor mount keyboard pole with articulating arm, tilt/swivel and universal keyboard tray. Pre-punched for Ford Crown Victoria.

LKP-FAR
Same as above without keyboard tray.
Accepts all motion attachments.

LKP-SKB
Vertical surface 9" to 13" adjustable keyboard pole with articulating arm, tilt/swivel and universal keyboard tray.

LKP-SAR
Same as above without keyboard tray.
Accepts all motion attachments.

LKP-CM
Universal 9" to 13" adjustable floor mount pole with articulating arm, tilt/swivel and ULTP4 universal laptop tray. Pre-punched for Ford Crown Victoria.

BRACE2
Adjustable 10"-16" support brace reduces mounting
system vibration. Attaches to pole with clamp
assembly and console, floor or dash on opposite end.
Attaches to any pole assembly.

BRACE3
Same as above, with 3 section adjustable
from 16"-34.
Attaches to any pole assembly.

FP-212
Short Stack radio mount fits under dash on hump or any flat surface. The angled base plate allows equipment to be placed for optimal accessibility. Brackets can be adjusted for various equipment.

RW-TSMT
(Shown with TS-60) Rear Wall Mount telescopes from 17" to 23" and features adjustable 180° swing with lock and tilt/swivel. 8"x 8" 9ga. mounting plate and welded construction for added strength. Mounts to a vertical surface or wall in trucks, vans or specialty vehicles. Attaches to any motion device.

spring steel bar code scanner clip for Control-Com consoles
BCR-CLP
Powder Coated Scanner Clip.

FP-LIFT
2 position Gas Spring adjustable Base 7"- 11" high with 4" slide.


	Control-Com Mounting Systems Printer Mounts and Special Mounts Printer Mounts PPJ-CASE Designed for use with the Pentax PocketJet mobile printers, it utilizes roll paper or cut-sheet depending on user preference. Roll paper is mounted in an enclosure designed to provide protection from prolonged exposure to direct sunlight. The “Fast Release” design allows rapid docking and un-docking of the printer for printing outside the vehicle. This mount is sufficiently compact that it may be mounted inside the glove compartment of many vehicles, or it may be used in pedestal or console configurations. PPJ-CASE-AP Same as above with armrest pad. CV-PPJ-GB New Part Designed to securely mount the Pentax PocketJet mobile printer in the Ford Crown Victoria glove box. The 16” articulating arm allows the printer to pull out for easy access and to be folded and stored within the closed glove box. PPJ-HDRM-WF New Part Armrest mount for Pentax PocketJet printer on a 5”- 8” adjustable wide flange pole mounts directly to base plate. Pull-pin latching cover lifts for easy printer and paper access plus paper roller allows simple lift out paper changing. Molded poly armrest pad flips up for easy access to equipment. Constructed of 14 ga. powder coated steel. Dminsions: 10.5” L x 6.0” W x 4.25” H PPJ-HDARM-VP Same as above with a 5”- 8” adjustable vertical pole which mounts directly to rear of console or vertical surface. PRBKT-EP590 Designed to securely mount Epson 590 printers vertically or horizontally in your vehicle, it features a bale bracket to hold printer in place, and an adjustable paper guide with form feeder. Mounts to any motion attachment or assembly. PRBKT-RW420 New Part Securely mounts the Zebra RW-420 mobile printer in your vehicle Locking quick-release spring mechanism Vinyl bumpers protect printer Mounts to any Lund motion attachment or assembly Compact design weighs only 1.5 lbs Made of black powder coated 14ga. steel Dimensions: 7.0”L x 6.0”W x 2.375” PRBKT-HP450 The PRBKT-HP450 securely mounts the HP450 printer to Lund's PM-KBAD or PM-CPU adapter mounting platforms as well as to any motion attachment or assembly. The mount is constructed of powder coated steel and features padding on all contact points. Its lightweight design produces a weight of only 2.3 pounds. PRBKT-BJC The PRBKT-BJC Printer Mount secures the Canon BJC-85 printer to Lund's PM-KBAD or PM-CPU mounting platforms as well as to any motion attachment or assembly. The mount is constructed of powder coated steel and weighs only 4 pounds. The printer can easily be removed for use outside of the vehicle. PRBKT-I70 The PRBKT-I70 Printer Mount securely attaches the Canon i70 or Canon i80 printer to Lund's PM-KBAD or PM-CPU mounting platforms as well as to any motion attachment or assembly. The mount is constructed of powder coated steel, is depth adjustable from 7' to 8.78" and weighs only 2.14 pounds. The printer mount can be used with or without the optional battery pack.

	Next

Lund Industries, Inc.
303 Messner Dr. - Wheeling IL 60090
Phone: 847.459.1460 Fax: 847.459.1569
toll-free 800.504.1460